Does plastic thermoforming equipment have any requirements for the thickness of raw materials?

Sep 26, 2025

Leave a message

Plastic thermoforming equipment does have specific requirements for the thickness of raw materials, depending on the type of equipment, molding process and end use of the product. Here's a breakdown:
1.Limitations on the thickness of raw materials by type of equipment
Manual/Semi-Automatic Equipment
Application: Typically suitable for sheets between 0.1 and 5mm. Some simpler devices can only support flakes less than 0.5mm thick.
Reason: Manual operation requires manual control of heating and molding. Thick plate will lead to uneven heating or insufficient molding force, affecting the accuracy of the product.
For example, Small laboratory thermoforming machines are typically used to produce samples between 0.2mm and 2mm, such as drug packaging trays.
Fully automated equipment
Application: Processing of plates between 0.05 and 10mm. High-end devices can even handle plates more than 15mm thick.
Reason: Automation ensures uniform deformation of thick plates by precisely controlling heating temperature, molding pressure and cooling time.
For example, automotive interiors production lines typically use ABS or PC plates between 3mm and 8mm and are efficiently molded using multiple rotary machines. Specialized Equipment (e.g. Overmolding Machines)
Scope of application: suitable for special products, thickness range is narrow. For example, bathtub molding machines usually use acrylic sheets between 5mm and 12mm.
Why: Professional molds and hydraulic systems must match the thickness of the plate to ensure structural strength and surface quality.

 

ii. Process Requirements for forming Raw Material Thickness
Vacuum Forming
Optimal thickness: 0.1-3mm. Due to the lack of vacuum pressure, too thick Sheetss may not adhere well to the mold, resulting in indentations or creases.
Improvements: Double vacuum chamber design or additional auxiliary air pressure can be used to extend the range to 5mm plates (e.g. large storage boxes).
Air Pressure Forming
Optimal thickness: 0.5-8mm. Compressed air can deform thick plate quickly and is suitable for deep drawing products.
Limitations: Thin plates (<0.3mm) may break due to high pressure and pressure parameters require to be adjusted.
Plunger-Assisted Pressure Forming
Optimal thickness: 1mm to 15mm. The plunger apply additional pressure to optimize wall thickness uniformity of thicker plates. Uses: Used in the production of 5mm -10mm industrial containers, such as chemical drums.

info-1-1

III. Effects of Raw Material Thickness on product quality
Wall Thickness Uniformity
Sheet (<1mm): Rapid heating can easily lead to localized thinning and requires infrared zone heating to temperature control.
Thick plates (>5mm): Extended heating time or increased temperatures are required to ensure complete softening of the interior and avoid "cooked" products.
Forming accuracy
Sheet: Suitable for producing high precision products such as electronic component trays, but easy to produce mold surface roughness.
Thick plates: High molding pressure (e.g. hydraulic system pressure ≥10MPa) is required to minimize rebound and deformation.
Production Efficiency
Sheet: Short heating time (typically <10 seconds), suitable for high speed continuous production (e.g. food packaging).
Thick plates: Extend heating and cooling times (which can be as long as a few minutes) and optimize equipment cycle times to balance efficiency. IV. INTRODUCTION Recommendations for Thickness Selection in practical applications
Determine thickness according to product application.
Disposable tableware: Opt for 0.2mm -0.5mm PS or PET sheets to keep costs down.
Auto interior: 2mm-5mm ABS or PC/ABS alloys to meet flame retardancy and impact resistance requirements.
Industrial containers: 8mm to 12mm HDPE sheets are used to ensure chemical stability and pressure resistance.
Adjust thickness according to equipment capabilities.
If your device supports plates between 0.1mm and 6mm, but production is low for products larger than 4mm, you may need to:
Upgrading heating system (e.g. increasing the number of quartz tubes);
Replace high precision die (e.g., a hard chrome electroplating mold);
Optimize process parameters (e.g. increase molding temperature by 5°C to 10°C).
Take material shrinkage. Thick plates (e.g., PP) can contract 2% to 3%. Therefore, compensation is allowed in mold design to avoid product size deviation.

Send Inquiry